Tutorial on Knapping Flint Arrowhead and making an Arrow


Recommended Posts

  • 1 month later...

Here is a great video explaining the process of getting spalls for blades from a large cobble/core. This is the first step in preparing adhoc stone cutting tools. After you get these spalls, the larger spalls can be turned into large biface tools such as blades or points and the smaller spalls are useful as ad hoc blades.

He briefly talks Direct Percussion using Antler tines at 2:00 however this entire process is done using a soft hammer-stone and abrading stone.
Platforms on ridges, force of hit, He gets into preparing platforms for striking around 6:00.
He has plenty of discussion about using minimal force to strike off the blades as well as the necessary support points and aiming the flake by the direction of the stroke.
The result is a core and about 7 blades that could be used as rough cutting blades, probably hafted.


Link to comment
Share on other sites

I want to introduce some of the very important technical terms and here is a link to a basic reference. http://www.flintknappingtools.com/terms.html


Flintknapping Terminology

Here are some helpful descriptive terms commonly used in knapping...

For definitions on Tools, click here

Abrading... The process of polishing the edge of a preform's platform to strengthen the it in preparation for flake removal by percussion or pressure flaking.

Biface... A spall or piece of flint that has been flaked on both sides.

Bulb... Often called "The bulb of percussion" it is the area very close to the edge or margin of the biface where the flake originates due to pressure or percussion work. It can sometimes be deep and cause significant concavities along the edge. The bulb should be kept at a minimum. See drawing

Center Line...This term is used to describe the imaginary centerline of a preform as viewed from the blade edge. See drawing

Cobble...Some flints occur in cobble form. These are irregular shaped but smooth, and are formed in various sizes averaging from one to 5 pounds and are generally covered with a cortex.

Concave... A"cupped" area on the face of a preform or nodule. This should be avoided until the material around it has been removed thus raising this "negative" area to match the contour of the rest of the Blade or core.

Convex... The opposite of concaved. It is a rounded raised area. A lens shape is a good example. This is the foundation for good successful flaking!

Core... The "mother stone" or nodule which spalls are removed from. Also a carefully prepared worked piece of flint that Sharp useable blades are removed from.

Cortex... The outer "skin" of a flint nodule or spall. Usually a chalky white or brown material ranging from 1" to 1/4" thick.

Flake... A thin, sometimes broad and sharp piece of stone chipped from a larger biface or preform.

Flake Scar... This is the "scar" left behind where a flake has been removed.

Flute Flake... A special flake removed from the base of a blade or preform that travels up the face towards the tip. The purpose of this flake was to create a concaved channel to aid in the special hafting technique of Paleo era points.

Heat Treating... Flint was often heat treated by North American peoples. Things are no different today! The flint is very slowly heated and cooled to temperatures ranging from 350-700 F, depending on the material quality and type. Not all flints benefit from heat treating. Heat treating gives the flint a glass like attribute making it easier to chip.

Hinge Fracture... This is an undesirable flake that falls short of it's mark by " rolling" out. See image.

Isolated Platform... This is a platform that has been "isolated" from the material around it. This is done by carefully chipping the stone away from either side of it. This leaves the platform sticking out a bit. The energy is transfered much farther "down range" using isolations.

Knapping... The skillful act of chipping flint or making gun flints.

Margin... The edge or circumference of the biface or preform.

Nodule... A large to very large smooth or irregular piece of flint.

Overshot Flake... The affect of a flake that travels from one margin to the other and "clipping" the opposite edge.

Platform... A platform has 3 main components, this is discussed in "platforms". A carefully prepared area on the edge of a preform to be struck to create the desired flake. Or A naturally occurring area on a rough spall or nodule that would produce a desired flake or spall. Platforms are the key to good knapping.

Platform Bevel... This is the part of the platform that is actually struck.

Platform Support... This is the underside of the "bevel". It gives support to the platform at the time of strike.

Platform deltas... These are the results of flake removal. See drawing

Preform... A bifaced blade in various stages of reduction.

Pressure Flaking... The act of removing flakes by pressure using an "Ishi Stick" or flaker.

Percussion Flaking... Removing flakes by directly striking the stone with a billet.

Raking and Shearing... Raking is the action of carefully dragging a course abrader or other device to remove "micro" flakes from the edge of a biface or preform to change it's shape or give support to an edge before actual abrading is done prior to percussion or pressure work.

Spalling... The act of breaking up a nodule or cobble into workable and desirable sized pieces.

Spalls... The finished untrimmed large flake removed from a larger "mother" stone.

Stack... Another BAD thing. A series flakes that fall short of a single specific objective. Resulting in multiple failed attempts to remove a specific problem area. Read"Platforms" for preventative measures.

Step Fracture... A single flake falling short of it's mark by creating a "step" on the surface of the Blade. The thinner you get the more this demon haunts you.


Link to comment
Share on other sites

Lastly, I want to share a channel from a highly recommended flint knapping teacher, Paleomanjim. I'm just starting to work through his material. What I need to do is consolidate this stuff into a concise summary, knapping 101. Or find a concise summary itself which will be easier.

Here are his playlists on various aboriginal technology topics but especially on knapping.

Flintknapping - Beginners Part 1


Your comments and observations will be very welcome: all those interested in paleolithic technology.

Link to comment
Share on other sites

Here is an example of a weapon made from blades obtained from the blade/core technology. Note, this is not an axe for chopping wood; it is purely a weapon mainly for warfare but perhaps for defence from jaguars too.


Link to comment
Share on other sites

  • 1 month later...

In my experience, bone projectile points suck. Not because they are ineffective (quite the contrary)

but because they take so long to make. When making bone arrowheads, you have to 1) find a piece of bone thick enough, 2) break it off in a rough arrowhead shape, 3) Spend at least an hour (without tools) grinding the thing down (not to mention that you don't want to inhale the bone dust).

Compare that to a shard of glass that you flake off a bottle-bottom. Not even a knapped biface, just a shard of glass. If it breaks, or if the point falls off, who cares? Knock off another flake.


Using plain stone/glass flakes are almost infinitely easier than trying to knapp a biface, they take almost infinitely less time, and they are just as effective. Take a shard of glass that you would use in the above fashion as an arrowhead, and lash it into a stick perpendicular to the shaft. Boom, a "hoko knife" that you can use for basically everything.

Unless I am going to be making points (note that biface arrowheads are also exceptionally good as "dagger"-style knife blades) for trade, I would not waste  my time making biface points.

Link to comment
Share on other sites


This topic is now archived and is closed to further replies.